Product Code: DEGHEATSHIN2700BLACK
Delivery: 3 weeks
|Description||Degxel Electric Infrared Heater 2700W for outdoor sheltered areas|
|Structure||Anodized aluminum infrared heating bar (black front)|
|Use||Outdoor heating (covered or sheltered from the wind otherwise it can reduce its performances) : verandas, patios, terraces, winter gardens, historic buildings, balconies and porches, pergolas, wellness or spa, summer lounges, etc|
Also suitable for indoor with high ceiling where it is not possible to heat the entire volume (churches, stone buildings, etc.).
|Heating Power||Heating power* = Consumption = Max power output = 2700W. Instant heat and maximum power in 1 minute.|
Radiation efficiency 76% ! Power at 2 m = 220W/m2
|Heating Radiation||Radiation angle of 90°.|
IRB infrared heating : 1400nm-5000nm
|Heating Volume||Heats up to 12 m² outside up to 3 meters of distance (height). Reduced if subjected to drafts.|
Heats approximately 20 m² inside to 3 meters of distance (height). Reduced if subjected to drafts. Please note that in exposed areas with wind the infrared spread may be reduced by 1/3 to 1/2.
To place ideally at height between 2.2 meters and 2.5 meters (3 meters max.) above the heated area. Can also be placed on the ceiling. The unit must be oriented directly towards people to heat. Do not place anything within 80 cm from the heat emitter.
|Technology||Electric infrared heater for outdoor (carbon-based technology)|
|Material||Anodized aluminum profile|
Emitter from carbon tubes (3 tubes of 900W each)
Black. White on specific request.
|Dimensions||Length: 125 cm, Width: 17 cm, Thickness: 8 cm|
|Temperature||Surface/filament temperature: approximately 1100°C|
|Attachement||Suspended (ideal height 2.3 meters). 1 kit for ceiling mounting is included by default. To be inserted into the rear groove provided for this purpose. For other attachment solutions please see the end of the page or contact us.|
|Mounting||Fast and easy. Simple and quick. Installation Manual supplied (english).|
|Electrical connection||Standard power supply line: 16A, 230V, 50Hz. Standard cable to be connected to the network (without socket 3 x 1.5 mm2 – length: 1,5 meters). Power 12A.|
|Monitoring system||Supplied with 1 wireless remote-thermostat + 1 radio receiver (to be connected and mounted on a stable support). The remote sends the order (radio) to the receiver which switches on or off the heater. The thermostat function only makes sense for a covered outdoor or indoor use.|
|Warranty||2-years. After sale conducted in the UK|
|Maintenance||Replacing carbon tubes (3 x 900 Watts). 50£ per tube (available all year round)|
|Origin||100% made in Germany.|
|Security||IPX5, class 1, CE, TÜV, GS, ROHS|
|Delivery time||3 weeks|
See the principle of infrared heating. The advantages of heating by infrared radiation are many. The mastery of our infrared technology (based on a unique radiant emitter) combined with an innovative design and high-end materials ensures reliability, low energy consumption and durability. Last year we saved about 3300 Megawatts-hours (MW.h) to our customers! The DEGXEL heaters offer a soft and comfortable warmth for a consumption of 50-55 W per m2 (on average). This means that with our radiators you will need less power (to heat the same volume) than with conventional electric heaters (90 to 130 w / m2 most often). We will offer you a 750 W when you use a 1500 W! It is the low consumption.
Our infrared heating is intended for covered outdoor (and sheltered from the wind which can reduce its performances) : verandas, patios, terraces, winter gardens, historic buildings, balconies and porches, pergolas, wellness or spa, summer lounges, etc. It is also quite suitable for bathrooms in which to obtain a very quick and punctual increase of temperature is desired. Finally, it is also used by professionals who need to heat a defined area.
The ideal positioning of the infrared heater is located above the area to heat at 2-2.5 meters approximately. Also, when installing your device you need to think about the control system. This can be controled by any wired or wireless temperature management system. By default, the infrared heating system is delivered with a wireless thermostat which switches on and off the heater. Note that in the case of outdoor heaters the thermostat have mainly a role to switch on and off the heater (principle of a remote control). In fact the temperature measurement is less reliable than for internal heating. Setting up a control or temperature management system helps to reduce your consumption while creating a pleasant and relaxing atmosphere.
1 kit for ceiling mounting is included by default (picture below – 12 x 8 x 6 cm). To be inserted into the rear groove provided for this purpose.
For other attachment solutions please see options below.
£129 inc. VAT (1 kit of 2 articulated Rod)
By default, your heater comes with a ceiling mounting system. In case you want to fix the heating laterally and orient it precisely to an area to be heated, we have provided a kit of 2 articulations specially designed for this purpose. The kit is composed of 2 aluminum jaws (to fix and adjust the spacing) and two orientable joint-rod kneecaps. Place each rod on both side of the heater for a perfect stability. The oval plate below is not part of the kit.
£69 inc. VAT
These brackets are intended to insure the stability and orientation of the flow at a slope of 45° when mounting a DEGXEL infrared outdoor heater.
Dimensions: 103 x 85 x 116 mm
CE standards, made in Germany.
Guarantee: 2 years
£149 inc. VAT
These rods are intended to insure stability, security and styling when mounted on a DEGXEL infrared outdoor heater
Length 300 mm. Diameter: 27mm
There are possible extensions to lengthen the distance. Contact our customer service.
CE standards, made in Germany. Guarantee: 2 years.
£149 inc. VAT
These ropes are intended to insure stability, security and styling when mounted on a DEGXEL infrared heater
Length 150 cm
Easily adjustable in height
CE standards, made in Germany. Guarantee: 2 years
£69 inc. VAT (2 plates)
These plates are intended to provide additional stability when mounting the accessories for infrared heaters
Dimensions: 84 x 49 x 8 mm
CE standard, made in Germany. Warranty: 2 years
Wiring the heater must be connected in accordance with the relevant national electrical safety standards. For a discreet fitting (i.e. with all wires and sockets hidden), you may prefer to have the heater hardwired by a qualified professional? If so wished, we will be happy to put you in touch within your area (without any guarantee that the installation will be performed within a specific period). Please note that a standard complete installation (heater mouting + wiring) can be performed in less than 1h by any professional without any specific knowledge.